# Helidox (Corne) High Profile Acrylic Case Guide (Wave Case)

{% hint style="info" %}
NOTE: This guide is for one half of the case. Just mirror the steps for the other half :thumbsup:
{% endhint %}

<figure><img src="/files/XW4rivoCxw7jkxPK4prj" alt=""><figcaption></figcaption></figure>

## All Contents

<table><thead><tr><th width="298.3333333333333">Piece</th><th width="96">Amount</th><th>Image</th><th data-hidden></th></tr></thead><tbody><tr><td>Base </td><td>2</td><td><img src="/files/MH9kAPLANaCw2dZd4KX6" alt=""></td><td></td></tr><tr><td>Middle</td><td>6</td><td><img src="/files/rzHLFpO4hZE7mHZ0TmaH" alt=""></td><td></td></tr><tr><td>Plate</td><td>2</td><td><img src="/files/AnyAaSEK4o9GoMGqQMKq" alt=""></td><td></td></tr><tr><td>Top</td><td>4</td><td><img src="/files/FHSo0BUS6Gxvf3nE6NEO" alt=""></td><td></td></tr><tr><td>Middle Side Piece (Bigger Holes)</td><td>6</td><td><img src="/files/cPZUGyynuRffHbq3pacr" alt=""></td><td></td></tr><tr><td>Top Side Piece (Smaller Holes)</td><td>4</td><td><img src="/files/VdYKfM7tOFjrSq11eWCL" alt=""></td><td></td></tr><tr><td>Thin Side Piece</td><td>2</td><td><img src="/files/SFzl5tI3HKk6fNgTRTWU" alt=""></td><td></td></tr><tr><td>OLED Cover</td><td>2</td><td><img src="/files/66DWGInmxnFlIsi6Z43h" alt=""></td><td></td></tr><tr><td>6mm Screws</td><td>30</td><td><img src="/files/wugfJ3DickCzxy1ikQtT" alt=""></td><td></td></tr><tr><td>8mm Standoffs</td><td>15</td><td><img src="/files/oKW3teHHs37hggs5C5UF" alt=""></td><td></td></tr><tr><td>14mm Screws</td><td>8</td><td><img src="/files/Y15DhxObQVxuknOEWm8U" alt=""></td><td></td></tr><tr><td>10mm Screws</td><td>6</td><td><img src="/files/dLeMEGFUMRXgnSKJXBIb" alt=""></td><td></td></tr><tr><td>Rubber Feet</td><td>10</td><td><img src="/files/m6Xcg8MkMW1MPCvyYx7V" alt=""></td><td></td></tr></tbody></table>

## Build Steps (High Profile)

1 - Remove all protective film. Be careful not to scratch the acrylic pieces. Check all pieces are included. Let us know if anything is missing.

2 - Place a 6mm Screw through the Base Piece, protruding up

<figure><img src="/files/J8QBkBzNOs4Hvq04AaRz" alt=""><figcaption></figcaption></figure>

3 - Screw a 8mm Standoff onto the protruding screw

<figure><img src="/files/dOegQzPHUAAWVsJSeknl" alt=""><figcaption></figcaption></figure>

4 - Repeat steps 1 & 2 for all remaining holes on the base plate. Screw these tight

<figure><img src="/files/FoO9DrKQ8vEU09DoJ00i" alt=""><figcaption></figcaption></figure>

5 - Place 3 x Middle Piece onto the protruding standoffs

<figure><img src="/files/N0cuf6zz1DrMGYGNTCWJ" alt=""><figcaption></figcaption></figure>

6 - Place 3 x Side Piece onto the remaining protruding standoffs

<figure><img src="/files/URXCyBerLYitioT5UOhh" alt=""><figcaption></figcaption></figure>

7 - Place the switch plate on top of the case so far. The plate should already have your switches and PCB installed. Make sure to **REMOVE** your existing OLED Cover.&#x20;

<figure><img src="/files/tyFBw9pEDBjGpnEpBpHH" alt=""><figcaption></figcaption></figure>

8 - Add the tops layers, and screw everything together using the 14mm screws

<figure><img src="/files/xHAOXNuk3rqQHAp62w0p" alt=""><figcaption></figcaption></figure>

9 - Separately, Add 2 x 14mm screws through the OLED Cover, through the top side piece, and through the thin side piece

<figure><img src="/files/NWwcmAQLtamy4nBUoSYY" alt=""><figcaption></figcaption></figure>

9 - Screw this into place near the controller. Add feet to the bottom of the case. **Your case is now complete!**

<figure><img src="/files/Dlq3408xhqz7DaQDWt8I" alt=""><figcaption></figcaption></figure>

## Build Guide (Low Profile)

Follow all steps above until step 7. Place the extra 6mm screws through the plate and the thin side piece and use your standard Helidox OLED Cover.


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://guides-mechboards.gitbook.io/guides/acrylic-guides/helidox-corne-high-profile-acrylic-case-guide-wave-case.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.