---
description: >-
  Congratulations on receiving your Hyper7, the journey ahead is long and
  arduous, but it'll be worth it,   I promise!
---

# Hyper7 R4 Build Guide (Enclosed Case)

## Building a Hyper7 R4:

### Materials Needed:

* Hyper7 R4 PCB
* Hyper7 enclosed case
* Hyper7 plate
* Foam
* 17 x Case screws
* (Up to) 220 x Switches
* (Up to) 34 x Stabilisers
* USB extender
* Handle with washers and nuts
* Feet x 6
* Keycaps

### Steps

1.  **Check Contents:**\
    We'd like to think everyone will have exactly what they need, but we're only human, we make mistakes. Please check through everything you've received to make sure there's nothing missing/damaged and let us know if there's something we've messed up on!

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FxSyIzHGn6q5wmEPSAawx%2FBuild%20Guide_0034_Layer%202.jpg?alt=media&#x26;token=087c3446-d19c-42cb-b74d-8cd971b1ad43" alt=""><figcaption><p>That's a lotta keyboard!</p></figcaption></figure>
2.  **Check Alignment + Remove Plate Vinyl:**\
    We'll try to check this too, but it's worth checking the screw holes on the plate line-up with the holes on the case, they should be as pictured below:

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FRsUpFEOK47hqvyG2NmRE%2FBuild%20Guide_0001_Layer%206.jpg?alt=media&#x26;token=34e59e97-bed2-4890-906e-614f4654b409" alt=""><figcaption><p>Checking the plate and case holes line up</p></figcaption></figure>

    If they're not quite close enough, don't be afraid to give the plate a little bend to get them into place. Trust me, it'll survive.\
    We can also remove the protective vinyl on the plate.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F80DYXl3zsjDpaxf8xoc0%2FBuild%20Guide_0031_Layer%203.jpg?alt=media&#x26;token=8838bd53-ffff-456e-bcbd-3a8e47f01a29" alt=""><figcaption><p>Peeling off the protective vinyl</p></figcaption></figure>
3.  **Check PCB:**\
    Last little QC here, please plug in the PCB to make sure it's working, feel free to pop in a couple of switches to check keypresses are being registered too!

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FgQRuoUOkkLknAXtUr0ET%2FBuild%20Guide_0033_Generative%20Fill%205.jpg?alt=media&#x26;token=16f28c7f-88b3-473b-a71d-833153683d8c" alt=""><figcaption><p>The big beautiful PCB</p></figcaption></figure>
4.  **Installing Stabilisers:**\
    First off is the stabilisers, _<mark style="color:red;">**if you're using GMK, clipping them is absolutely essential (if you're unsure on how to do this, please watch**</mark>_ [_<mark style="color:red;">**this**</mark>_](https://youtu.be/usNx1_d0HbQ?t=171)_<mark style="color:red;">**).**</mark>_\
    Now we can begin to insert and screw them in, if you've built keyboards in the past this should be a nice, easy and monotonous task!

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FEhLk3jOmPGBWektGDze0%2FBuild%20Guide_0030_IMG_5511.jpg?alt=media&#x26;token=6dbe2755-9e06-4da6-bbf0-4800b21dcec8" alt=""><figcaption><p>Installing a stabiliser</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FbcLC4akF33s4IPTNrKpM%2FBuild%20Guide_0029_Generative%20Fill%209.jpg?alt=media&#x26;token=3e165049-ec95-4dbe-b920-d9b5558b03c8" alt=""><figcaption><p>All stabilisers installed!</p></figcaption></figure>
5.  **Installing Switches:**\
    Next up, add switches to a few locations around the plate, roughly around the corners and middle sections will help the most.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F2RJSYyQMAKvtVyHw4lUD%2FBuild%20Guide_0028_Generative%20Fill%2010.jpg?alt=media&#x26;token=7c5ba79d-6a2b-4051-8b20-fbf91e26c42f" alt=""><figcaption><p>These are the 'strategic' switch placements we went with</p></figcaption></figure>

    Now turn over the plate and very carefully push the PCB onto the switches, make sure the plastic pins are lined up with the holes on the PCB, this will be the best indicator for the metal pins lining up with the hotswap sockets. _<mark style="color:red;">**Please take care whilst doing this, if the switch pins are not aligned properly the hotswap sockets can become damaged and will require soldering to replace them.**</mark>_

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F9aPvspNfEMT9tLa8YEiQ%2FBuild%20Guide_0026_IMG_5529.jpg?alt=media&#x26;token=3531957a-8ab4-4473-85c5-ec0ece4e2d27" alt=""><figcaption><p>Pushing the PCB onto the switches</p></figcaption></figure>

    Once the PCB is attached, you can turn it all over again and insert the rest of the switches one by one, continuing to make sure the pins are aligned with the hotswap sockets.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FXy2DNv1Whpa6jVu5mrn1%2FBuild%20Guide_0025_IMG_5542.jpg?alt=media&#x26;token=ecca400c-c41a-4bfa-8366-3557273ab680" alt=""><figcaption><p>Makng sure to press the PCB while inserting the switch</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2Fv5eWzXUC7h1XXSHEHGGN%2FBuild%20Guide_0024_IMG_5545.jpg?alt=media&#x26;token=5cfe432d-396f-4aa6-8d4e-25c447c71c07" alt=""><figcaption><p>Same as above for the bottom half!</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FelwzPWxGdUYhrsjxpGZB%2FBuild%20Guide_0023_Generative%20Fill%207.jpg?alt=media&#x26;token=3707ae9b-4978-417b-9ddc-f4756b7a4ab5" alt=""><figcaption><p>All switches inserted!</p></figcaption></figure>
6.  **Installing USB Extender + Handle:**\
    Now we need to plug the USB extender into the PCB and attach the handle to the case top. This should be nice and simple, but will be a lot tougher/impossible if it's not done now.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F95hnymR6mQVra7HeLomD%2FBuild%20Guide_0022_IMG_5548.jpg?alt=media&#x26;token=56b9b734-60af-4666-b4d3-b81f15c08111" alt=""><figcaption><p>Plugging the USB extender</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FhF5sJbe63vSBDoFsfefB%2FBuild%20Guide_0021_IMG_5552.jpg?alt=media&#x26;token=c373304d-f34d-4769-a5b5-6773bd4df0fb" alt=""><figcaption><p>Don't forget to put the washer under the nut!</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FbSbAsqwwlAseq1mXQ9hb%2FBuild%20Guide_0020_IMG_5558.jpg?alt=media&#x26;token=a27f6858-dac8-41a5-b75a-6eed929cc0e1" alt=""><figcaption><p>We go for the downwards handle orientation here</p></figcaption></figure>
7.  Installing Plate onto Case Bottom:\
    We can now turn over the plate and gently place the case bottom on top, with all of our screw holes we checked earlier (**You checked them in step 1. Right?**) lining up perfectly.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F56XwhfxSwfyFDEZKTp3T%2FBuild%20Guide_0019_IMG_5559.jpg?alt=media&#x26;token=79cf1d66-7950-4836-be35-69c2ab540665" alt=""><figcaption><p>Right side</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FAbgKN9H89TyE0mUrAdit%2FBuild%20Guide_0018_IMG_5560.jpg?alt=media&#x26;token=67e4cd1e-45a1-48c4-bae7-92fdb9b3c95f" alt=""><figcaption><p>Left side</p></figcaption></figure>

    Now screw through the case bottom into the plate, we recommend screwing them all loosely first (starting with opposing corners) and then tightening them after.

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FI25kLb2xBP3dCzqjGhgz%2FBuild%20Guide_0017_IMG_5563.jpg?alt=media&#x26;token=be3d1b09-e59b-457c-a7b9-ca147c7bdc80" alt=""><figcaption><p>Screwing (professionally)</p></figcaption></figure>
8.  Connecting USB Extender to Case + Inserting Foam:\
    Next, turn the case + plate the right way around and screw in the other end of the USB extender into the top case. This is also the best time to insert your foam under the PCB!

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FEaMMC88NfMrotZFFLYGS%2FBuild%20Guide_0015_IMG_5573.jpg?alt=media&#x26;token=6230dcd7-85d0-49a9-bf57-96265dcbe47a" alt=""><figcaption><p>This is how I like to orientate the keeb for this part</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FpZAOQ4Hza7vsGvl50rPO%2FBuild%20Guide_0014_IMG_5577.jpg?alt=media&#x26;token=3c53138f-6768-4ab7-878b-9bbb1e6599c5" alt=""><figcaption><p>Screwing the exteneder to the back of the case top</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FQLO5jdQIT2RyAmJ5rcbM%2FBuild%20Guide_0013_IMG_5579.jpg?alt=media&#x26;token=0382f26a-aa66-4f27-8364-8b106a86c456" alt=""><figcaption><p>Inserting the foam</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FOafwrC54ooyJxv08sRBB%2FBuild%20Guide_0012_IMG_5581.jpg?alt=media&#x26;token=86eda703-0220-493c-8c25-ed472cc5550c" alt=""><figcaption><p>Folding and tucking</p></figcaption></figure>
9.  Installing Case Top:\
    Now to finish off the case, take the case top and bring to over the top of the rest of the build. Screw in the 4 screws on the back, and the 5 on the bottom. We're almost there!

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FVfMwx2LTm5OKIhWWgHej%2FBuild%20Guide_0011_IMG_5594.jpg?alt=media&#x26;token=c71b027f-1d3d-41fe-a49a-02c6d098f26a" alt=""><figcaption><p>Placing the top half of the case</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FBLYYL70ZmEliaKCyHe8c%2FBuild%20Guide_0010_IMG_5596.jpg?alt=media&#x26;token=bc41f69a-2a8e-4a82-8c32-8bc2d2e5c4f2" alt=""><figcaption><p>Keeping things nice and aligned</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F3OR4vEUsJ3KaciW6YJpH%2FBuild%20Guide_0009_IMG_5598.jpg?alt=media&#x26;token=7dac2bf7-3c4a-4373-bfbc-1c284f24dcb3" alt=""><figcaption><p>Screwing the back of the case</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2F3KmBjUpAmVFjlFLcbX0I%2FBuild%20Guide_0008_IMG_5600.jpg?alt=media&#x26;token=8712e46e-0dc8-4322-a16f-611e28d4b46c" alt=""><figcaption><p>A little bend could be required here if things don't line up perfectly</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FSgKZpLj1vupJneW4IYMq%2FBuild%20Guide_0007_IMG_5603.jpg?alt=media&#x26;token=7b403715-4df4-4ac9-af31-26d8879641eb" alt=""><figcaption><p>Screwing the bottom of the case one</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FiH3mF1l0dePGA8kD2Ugo%2FBuild%20Guide_0006_IMG_5604.jpg?alt=media&#x26;token=d144605e-4faf-43cd-bd61-95359981a4ec" alt=""><figcaption><p>Almost done!</p></figcaption></figure>
10. Installing Keycaps:\
    Finally, you can now pop the keycaps on with your chosen layout/legends. _<mark style="color:red;">**Do not push your 2U keycaps too hard, this will result in a mushy stabiliser that will likely get stuck. If you find this is the case, remove the keycap and reapply it with less force.**</mark>_

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FT7d6kiYkfpGGkckhIXte%2FBuild%20Guide_0005_IMG_5613.jpg?alt=media&#x26;token=4961f84a-1c98-4275-b8a0-e6ffdde4cdc6" alt=""><figcaption><p>Applying keycaps (cautiously)</p></figcaption></figure>

    <figure><img src="https://456586235-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F6bjiReLol1HqmhjbjtT5%2Fuploads%2FlwEixpjzqvF405YOsmyI%2FBuild%20Guide_0003_Layer%205.jpg?alt=media&#x26;token=6a9fa0a4-fd71-40ef-9150-38eaf7203346" alt=""><figcaption><p>All done!</p></figcaption></figure>
11. Installing Feet:\
    Pop on your feet however you'd like, we go for one in each corner and then one each in the middle on the top and bottom.
12. Plug and Play!:\
    And that's it, you can now go ahead and customise all the keys to your hearts content!

